Devices You Need to Set Up a New Tub
Devices You Need to Set Up a New Tub
Blog Article
Were you interested in details around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is readily obtainable, the job can move speedily; if you need to open up a wall to remove the old bathtub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you install a brand-new tub in your washroom if you have already gotten a new bathtub and do not need to transform the arrangement of your previous water pipes.
Your devices and product checklist need to comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the faucet in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and examine all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet and also the normal electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub should wait up until the bathtub has actually been used a minimum of once as this will certainly resolve it into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water before securing, to enable the motion experienced when the tub remains in use. The sealant can split relatively early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our piece about How to Install a Bathtub Yourself. Thanks for finding the time to browse our blog. Sharing is caring. You never know, you could be helping someone out. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit The Following Page
Report this page